Alvarion BreezeACCESS 900 Manuál s instrukcemi Strana 64
- Strana / 324
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
1-16
BreezeACCESS Version 4.5 Installation
Manual Revision: 1.0
The BS-PS
The BS-PS provides power to all the modules installed in the BS-SH
chassis. The BS-PS front panel is shown in Figure 1-10‚ page 1-16.
Figure 1-10: BS-PS Front Panel
The BS-PS provides a power input connector (marked -48V) for
connecting the -48VDC power source to the module. The color codes of
the cable wires are:
Black -48 VDC
Red + (Return)
The power switch turns the mains power to the power supply ON and
OFF.
Table 1-7: BS-PS LEDs
LED Description
ON -48 VDC is available and power supply is on
5V The 5V power supply module is OK and power is consumed (at least one BS-AU
module is inserted)
12V The 12V power supply module is OK and power is consumed (at least one
AU-RA/RE unit is connected)
- BreezeACCESS II 1
- System Manual 1
- Trade Names 3
- Statement of Conditions 3
- Warranties; Disclaimers 3
- Limitation Of Liability 4
- Electronic Emission Notice 4
- FCC Radiation Hazard Warning 4
- Important Notice 5
- Table of Contents 7
- System Manual Book 2: 8
- System Manual Book 3: 10
- Commissioning 10
- Manual Revision 1.0 11
- System Manual Book 4: 12
- Operations and Administration 12
- System Manual: Appendices 13
- Introduction 17
- Introducing BreezeACCESS 18
- Components 19
- Subscriber Units (Customer 20
- Premises Equipment) 20
- System Components 21
- Data-only Units: 23
- Data and Voice Units: 23
- Base Station Equipment 24
- GU-A-BS GPS and Alarms System 26
- Access Unit 28
- Networking Equipment 30
- Management Systems 30
- BreezeCONFIG 31
- Specifications 33
- System Specifications 34
- Standards 35
- Data Communication 35
- Configuration and Management 37
- GU-RA GPS Radio 37
- GU-RA to BS-GU Communication 37
- Environmental 38
- Standards Compliance, General 38
- Physical Specifications 39
- Connectors 40
- Electrical 40
- Mechanical 40
- SU-I/I-D 43
- AU-I/I-D 44
- SU-R Subscriber Units 45
- IF-Based 49
- Equipment 49
- Packing Lists 50
- Other Items Required for 51
- Installation 51
- Guidelines for Selection of 53
- Equipment Locations 53
- IF Cable 54
- Indoor Equipment 54
- Installing the Outdoor Unit 55
- Table 1-5: AU-RA/RE LEDs 56
- IF Based Equipment 57
- Connecting the Antenna Cable 60
- (SU-RE and AU-RE) 60
- Indoor Unit 61
- Installing Modular Base 63
- Station Equipment 63
- The BS-PS 64
- The BS-PS-AC 65
- The BS-AU 66
- BS-SH Chassis and Modules 67
- Installation Procedure 67
- Installing the GU-A-BS GPS 69
- Table 1-10: BS-GU Connectors 70
- Figure 1-14: GPS Installation 71
- Installing the BS-GU module 72
- SU-R Units 73
- Installation Guidelines 75
- Antenna Diversity 76
- Antenna Polarization 76
- Antenna Seal 76
- Lightning Protection 76
- Installing SU-R Indoor Units 77
- Connecting the Omni Antennas 78
- Supply and to the CPE 78
- Indoor SU-R Units 79
- SU-I and AU-I Units 81
- Indoor SU-I and AU-I Units 83
- Connectors and LEDs 87
- Table 3-2: SU-I LEDs 88
- Table 3-3: AU-I LEDs 89
- Wall Mounting the Unit 90
- Basic Parameters 95
- Configuration option 97
- Operating the Monitor Program 98
- Configuring Basic Parameters 99
- Manual Revision: 1.0 100
- Configuring Parameters in 101
- GU-A-BS Units 101
- Chapter 2 103
- Optimizing 103
- Configuring the Maximum 104
- Data Rate (Subscriber Units) 104
- Aligning the Antenna of the 105
- SU-A/E Subscriber Unit 105
- Configuring the Transmit 106
- Power of the AU-RE 106
- Optimizing the Wireless Link 107
- Positioning the SU-I or SU-R 108
- Subscriber Unit with Omni 108
- Antennas for Optimal 108
- Operation 108
- Chapter 3 111
- BS-GU Connectors 111
- Connecting External Devices 112
- OUT Connectors 112
- Alarms Out Cable 113
- GPS Cable 113
- SYNC Cable 115
- Chapter 4 117
- Verifying 117
- Proper Operation 117
- Verifying Connectivity 118
- GU-A-BS GPS Unit 119
- LED Indicators 120
- BS-PS DC Power Supply Module 121
- BS-AU LEDs 122
- BS-GU LEDs 122
- SU-R LEDs 123
- SU-I/SU-I-D LEDs 123
- AU-I/AU-I-D LEDs 124
- Chapter 1 127
- Accessing the 127
- Monitor Program 127
- Accessing the Monitor 128
- Program using the RS 232 128
- MON Connector 128
- Program using Telnet 129
- Operating the Monitor 130
- Main Menu 132
- Info Screens Menu 133
- Show Basic Parameters 135
- Show Advanced Parameters 135
- Show All Parameters 135
- Unit Control Menu 136
- Menus and Parameters 137
- Basic Configuration Menu 144
- VLAN Parameters 145
- Security Parameters 145
- Site Survey Menu 146
- Wireless Link Counters 147
- Support Only) 149
- Ping Test (AU, SU and GU) 150
- (Available in SU Only) 151
- Per-rate Counters (AU and SU) 154
- ATPC Counter (AU and SU) 154
- AU Alarms (IF-based AU Only) 155
- Power Tests 156
- Association Tests 158
- AU Alarms Summary 158
- All Associations Lost Alarm 159
- High CRC Error Rate Alarm 162
- The AU Alarms Menu 164
- Advanced Configuration Menu 167
- ESSID Parameters 184
- Best AU Selection Parameters 185
- Power Control Parameters 188
- -.: Transmit Power Output 190
- (AU, SU and GU) 200
- Port options are available 201
- WARNING: 207
- Other Bridging Parameters 214
- RADIUS Parameters Menu 225
- (Subscriber Units only) 225
- Accounting Parameters Menu 227
- RADIUS Record Structure 228
- Wireless Media Security 231
- Voice Parameters 232
- Protocol Parameters 234
- National Telephony Parameters 240
- Special Features 245
- Line Testing 248
- Hopping Parameters (GU) 251
- Alarm Parameters (GU) 253
- Alarms In Names 254
- Alarms Out Names 254
- Alarms Out Control 255
- Show Alarm Parameters 255
- Appendix A: 259
- Configuration 259
- Download/Upload 259
- Appendix B: 261
- Software Version 261
- Loading Procedure 261
- Loading an Upgrade to a Unit 262
- Appendix B 263
- Appendix D: 267
- RSSI to dBm 267
- Conversion Table 267
- SU-A/E, AU-A/E 267
- SU-R and SU-I 269
- Appendix E: 271
- Parameters List 271
- Unit Control Parameters 271
- Site Survey Parameters 272
- IP Parameters 273
- Air Interface Parameters 274
- Parameter Unit Range Default 275
- Run-Time 275
- Network Management 277
- Parameters 277
- Bridge Parameters 279
- Performance Parameters 281
- Service Parameters 283
- RADIUS Parameters 284
- National Telephony 289
- Special Features Parameters 294
- Hopping Parameters 298
- Alarm Parameters 298
- Appendix F: 299
- Hopping Sequences 299
- Hopping Standards: Canada 301
- US FCC, International 302
- Hopping Standards: France 304
- Hopping Standards: Israel 305
- Hopping Standards: Japan 306
- Hopping Standards: Korea 308
- Hopping Standards: Spain 310
- Manual Revision:1.0 312
Související produkty a manuály pro Software Alvarion BreezeACCESS 900
Software Alvarion BreezeNET PRO.11 Uživatelská příručka
(209 stránky)
(209 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.074 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce